The fireplace below a Starfire base with
Copper Blue Topper
Cobalt Blue Topper
Dark Red Orange Topper
Cherry Red Topper
Jade Green Topper
Lime Green Topper
Lime Green Topper
and Lilac Topper
What make us different from anyone else is what we offer you as a selection. We offer hundreds of colors, sizes, textures, variations, categories and more importantly we set the standard which everyone else can only try to imitate us. We welcome your comments and suggestions so please send us your comments.Imitation is the highest form of flattery, thank you.
The fire pit below is in Newport Beach California at Newport Coast Development. We replaced a hot spark ignition which did not work, with our IPI (intermittent Pilot Ignition) electronic ignition system. The fire pit was 18" deep and 48" across. This is what was installed:
1 IPI Electronic Ignition for Natural Gas connected to a 1" gas line
1300 lbs crushed lava
144 lbs Clear base glass for a 2" fill over the crushed lava
36" triple stainless steel burner ring
20 lbs Clear Topper
20 lbs Cobalt Blue Topper
20 lbs Copper Blue Topper
We will show your from beginning to end:
Looked pretty nasty when we got there
We started to pour the crushed lava with our electronic ignition being raised to the surface by the lava rock
We built a double box to protect the equipment in the fire pit as well
The ring is now installed
The electronics can be accessed if ever there was a failure of the equipment and you can access it from the surface. Before the equipment was 20 inches below the surface, not a very good idea!
Now we poured the 144 lbs of Clear base over the crushed lava
We only did the fire pit, not the view. That came with the home. But one very impressive view!
Then we spread the Clear Topper, Cobalt Blue Topper and Copper Blue Topper over the Clear base
As you have looked at all of our pictures we would like you to know we use Crystals as our Toppers and Toppings. We don't use "Recycled" glass, ever! We are actually the only company that produces Crystals for fireplace and fire pits.
We tried to get pictures of it burning, but the flames just didn't show. Look above and you can see a flicker in the daylight. Actually the flames were over 16" tall but you can't see this in daylight.The contractor will get a few night pictures when they and if they can.
The fire table below is in Sackets Harbor New York with one very nice view. The colors that were used are:
Bronze base glass
Cobalt Blue Topper
The burner below is one of our FPPK's (fire pit propane kit). With this FPPK we set it up for Black Magic! This was table tested for the pictures. Hopefully the customer will send us pictures after and during installation. We first sent these pictures for the customers approval. Here you go! The pan below belongs to Scott Spector and he finally installed the fire pit in his back yard, WOW, one really nice backyard!
This is one of our propane pan burner with slight modifications.
As you can see around the lower edges it was leaking and yes we did fix this.
The fire pit below was built by Scott Spector in Florida. He started with an FPPK 30 which includes a 30" base plate and a double 24" stainless steel ring. Here we go from the beginning:
The propane line was run/ installed under the pavers.
The colors that were used are
1/2" Clear base,
Black Magic in the center,
Cobalt Blue Topper,
Cobalt Blue Light Topper
and our FPPK 30". That is our 30" propane burner. You can see the actual burner above burning before shipment and installation.
We don't have any pictures of the fire pit burning at Scott's but he did tel us that when he fired it up again he would try to send us a few pictures. Thanks Scott.
The fire pit below has a Clear Base Glass with Starfire Base Glass and 1/2" Starfire Base Glass, Yellow Amber Topper. Cobalt Blue Topper and Emerald Green Topper and a little bit of ICE ICE ICE Topper. The earth as the back yard and a lot of friends, wow!
The fire pit below has V Blue, V Blue Reflective and topped with Cobalt blue Topper
This next fireplace is a direct vent conversion and the glass that Charlene used was:
V Blue Reflective,
Copper Blue Topper,
Blue Luster Diamonds,
Black Silicone Carbide under the Blues,
Cobalt Blue Diamonds,
Sky Blue Diamonds
Cobalt Blue Square Ice.
I think she wanted it to POP and it did!
The fireplace below has
a StarfireStarfire base with:
Orange R140 Topper,
Ice Ice Ice,
Copper Blue and Steel Blue toppers.
The Orange R140 Topper is actually one of our chameleons, it turns to bright red when it gets hot and then changes back!
Our Copper Blue Topper is a chameleon as well. It turns to green and changes back to blue when cooled!
The fireplace below is in San Diego, California and the colors used were:
The end pictures show that the burner was too close the wall which was an easy fix by moving the burner forward.
This is where is went a little bit wrong, oops. We just had them move the burner forward and now its fine and the back wall was repainted.