Copper Blue G251CF Topper
ID code: Copper Blue G251CF Topper
The fire pit below has Ford Blue, Ford Blue Reflective, V Blue, V Blue Reflective, Turquoise Toppings, Deep Royal Toppings and Copper Blue Topper on a bed of 1/4" and 1/2" starfire
The fire pit below was a traditional lava rock fire pit
Now filled with lava rock (crushed 1/4" 3/8") over 3/8" 1/2" crushed. Remember the larger is under the smaller to keep the glass from falling through.
Above a flex line was installed to raise the ring to the surface. You don't want to leave the ring at the bottom unless you want an explosion or if you want to get rid of the significant other.
Below
Pour more crushed lava to make the desired shape of the fire pit and test burn for flame pattern.
Starfire base and a few other colors were added
Azurlite, Scarlet Topper, Red Topping, Ice, Copper Blue Topper, Copper Blue is a chameleon as when it gets hot it turns green and when it cools it turns back to blue!
Patterns, can you do better?
Pretty creative!
Great job and very creative.
The fire pit below has a clear base with 1/4" starfire and 1/2" starfire, Yellow Amber Topper. Cobalt Blue Topper and Emerald Green Topper and a little bit of ICE. The earth as the back yard and a lot of friends, wow!
The fireplace below is a direct vent self install by Norm. The colors used were: Starfire base, Cobalt Blue Topper, Pale Cobalt Blue Topper, Ice Ice Ice, Pale Gray Topper, Gray Topper and Copper Blue Topper.
We use a piece of stainless steel in the front to contain the glass to cover the burners and keep the glass level.
The fireplace below is a propane self build and installed by Norm Oppliger in St. Louis. It has a 1/4" starfire base with 1/2' starfire on top and topping with:
Light Aquamarine topper
Turquoise blue topper
Cerulean Blue topping
Copper blue topper
Scarlett topper
Ice Ice Ice
and a few of our diamonds
one great propane self install Norm!
We will be posting different ideas on fire pit covers we can build or design for your fire pit.
This fire pit is in Pasadena California. The base is ford blue and v blue topped with both colors in reflective. Then we topped it with cobalt blue topper, copper blue topper and lagoon topper. Then we made a simple tie cover to keep the pit looking great all of the time when it is not in use.
The fireplace below belongs to Ross Barnett in Florida. This was a ventless propane installation. Ross built a front wave design and we built a special wedge pan with the controls underneath. This is a remote control ventless burner. Great job Ross! The glass that was uses was:
Black and Black Reflective
Gray and Gray Reflective
Aquamarine Topper
Copper Blue Topper
Light Blue Tubes
Cobalt Blue Topper
Pale Cobalt Blue Topper
and here are the before and after pictures.
Above is before the wave
and below is the wave before out ventless burner was installed.
What makes us different from anyone else is that we allow you to exercise your imagination. If you see it, dream it, draw it, imagine it we can build it for you. Ross saw what we did for other customers and he came up with this very cool design for us to build for his family room, thanks Ross!
The fireplace below a starfire base with
Copper Blue Topper
Cobalt Blue Topper
Dark Red Orange Topper
Cherry Red Topper
Jade Green Topper
Lime Green Topper
Lime Green Topper
Black Topper
and Lilac Topper
What make us different from anyone else is what we offer you as a selection. We offer hundreds of colors, sizes, textures, variations, categories and more importantly we set the standard which everyone else can only try to imitate us. We welcome your comments and suggestions so please send us your comments.Imitation is the highest form of flattery, thank you.
The fire pit below has a clear base glass,
Cobalt Blue Topper,
Copper Blue Topper and
Azurlite base glass for one very nice fire pit and back yard!
The fire pit below is in Newport Beach California at Newport Coast Development. We replaced a hot spark ignition which did not work, with our IPI (intermittent Pilot Ignition) electronic ignition system. The fire pit was 18" deep and 48" across. This is what was installed:
1 IPI Electronic Ignition for Natural Gas connected to a 1" gas line
1300 lbs crushed lava
144 lbs Clear base glass for a 2" fill over the crushed lava
36" triple stainless steel burner ring
20 lbs Clear Topper
20 lbs Cobalt Blue Topper
20 lbs Copper Blue Topper
We will show your from beginning to end:
Looked pretty nasty when we got there
We started to pour the crushed lava with our electronic ignition being raised to the surface by the lava rock
We built a double box to protect the equipment in the fire pit as well
The ring is now installed
The electronics can be accessed if ever there was a failure of the equipment and you can access it from the surface. Before the equipment was 20 inches below the surface, not a very good idea!
Now we poured the 144 lbs of Clear base over the crushed lava
We only did the fire pit, not the view. That came with the home. But one very impressive view!
Then we spread the Clear Topper, Cobalt Blue Topper and Copper Blue Topper over the Clear base
As you have looked at all of our pictures we would like you to know we use Crystals as our toppers and toppings. We don't use "Recycled" glass, ever! We are actually the only company that produces Crystals for fireplace and fire pits.
We tried to get pictures of it burning, but the flames just didn't show. Look above and you can see a flicker in the daylight. Actually the flames were over 16" tall but you can't see this in daylight.The contractor will get a few night pictures when they and if they can.
The fire pit below is a custom fire pit in Covina California with one really great back yard design. This back yard was designed for great parties. If you look and see the glass wall with the etching you will also see the fire pit in the back ground. The glass that was used: Gray and Clear Pyrite base glass Gold Reflective Copper Blue Topper This is one really good looking table.
The next fireplace was a self installation by Chris in Palm Springs California. He used about 3" of a sand base under the Starfire base glass. Then he added:
Here we go:
